Description
Reproduction of the M/27 officer belt. This belt was used by all officers ranks, but also some NCOs during WW2.
These belts have been made according to original manufacturing instructions and compared to original examples.
The belt is made of 3 mm dark brown cowhide with a 1 mm medium brown cowhide reinforcement sewn on the back with golden yellow thread. The belt is 55 mm wide, has rounded edges and two embossed lines running along both edges. There is a double-pronged cast brass buckle and three D-rings: two for the shoulder strap and one for the sword hanger. The buckle and D-rings are original army surplus. There is a leather pad under the buckle which has the length stamped on. The belt has two belt loops which are both free floating between the buckle and D-rings. The end of the belt is tapered and there are nine pairs of holes for adjusting the length for 20 cm. The shoulder strap is fastened to the belt D-rings with leather tabs and brass buttons. The strap length can be adjusted for 15 cm with a brass buckle and 10 holes.
See the Size table tab above for belt and shoulder strap sizing information.
This is a made-to-order product. Sometimes it gets pretty busy, so it might take a week or two to manufacture.
Size table
Belt sizing
The stamped size of the belt is measured from the base of the buckle to the end of the belt, as per originals. You can see a table for the standard belt sizes below.
We suggest you select a belt where your waist circumference (measured with a tunic on) falls in the middle of the minimum and maximum circumferences. Then you can adjust the belt both ways according to what you are wearing.
| Belt size |
Circumference when fastened |
| Minimum (cm) |
Maximum (cm) |
Minimum (inch) |
Maximum (inch) |
| 80 |
52 |
72 |
20 1⁄2 |
28 3⁄8 |
| 90 |
62 |
82 |
24 7⁄16 |
32 5⁄16 |
| 100 |
72 |
92 |
28 3⁄8 |
36 1⁄4 |
| 110 |
82 |
102 |
32 5⁄16 |
40 3⁄16 |
| 120 |
92 |
112 |
36 1⁄4 |
44 1⁄8 |
| 130 |
102 |
122 |
40 3⁄16 |
48 1⁄16 |
Shoulder strap sizing
The shoulder strap length is measured from the end of the strap to the other end when the flaps are buttoned. This is the max length of the strap in centimeters when fastened. You can however adjust the strap 15 cm shorter using the buckle in 10 increments. You can see a table for the standard strap lengths below.
Measuring the strap length for yourself is a bit difficult, as you need to measure around your shoulder. We suggest you get someone to help you. You need a tape measure or a string you can measure after with a ruler.
We suggest you wear your tunic, overcoat and a belt if possible. Any belt or even a tied string around your waist will do. Make sure the belt / string is at the height you would wear your officer belt. This is usually at your natural waist, which is the narrowest point on your torso and should be somewhere above you navel. Use your tape measure to measure the length starting from the front left on your belt around your right shoulder and ending to the back left on your belt. The start and end of your measurement should be about 30 cm / 12 inches apart along the belt on your left side. This is how far the shoulder strap D-rings are from each other on the officer belt.
Please, contact us if you are unsure on how to do these measurements. We are glad to help.
| Shoulder strap length |
Minimum (cm) |
Maximum (cm) |
Minimum (inch) |
Maximum (inch) |
| 70 |
55 |
70 |
21 5⁄8 |
27 9⁄16 |
| 80 |
65 |
80 |
25 9⁄16 |
31 1⁄2 |
| 90 |
75 |
90 |
29 1⁄2 |
35 7⁄16 |
| 100 |
85 |
100 |
33 7⁄16 |
39 3⁄8 |
| 110 |
95 |
110 |
37 3⁄8 |
43 5⁄16 |
| 120 |
105 |
120 |
41 5⁄16 |
47 1⁄4 |
| 130 |
115 |
130 |
45 1⁄4 |
51 3⁄16 |
| 140 |
125 |
140 |
49 3⁄16 |
55 1⁄8 |
